Kwikset lock beeping red

Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.3. Press the Program button once more. When the LED flashes green and you hear two beeps, the lock has been reset.4. Perform the door handing process again to teach the lock the orientation of the door. 5.

Kwikset lock beeping red. Auto-lock automatically re-locks the door after unlocking. This feature is set to 30 seconds and is turned off by default. 1. Press program button once 2. Press button 'A' once 3. Press button '3-4' multiple times if needed to reach desired state. Green lock button means feature is enabled. Red lock button means feature is disabled. 4.

The Kwikset Home. Security on the outside, convenience on the inside. ... On my Smartcode 888, the lock button flashes red with fast beeping sounds for three to four ...

Press Lock button once7. Press "9" six times.8. Press Lock button once.If programming is successful, the keypad will flash green once with one beep.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure to enter a valid Mastercode in step 3 during your next attempt9.[SOLVED] Kwikset lock pairing · Other Devices ... The red light on the lock goes back on. After ... Look for the rapid flashing orange light. If you ...On my Smartcode 909/910, the lock beeps, the keypad flashes red, and the door cannot lock. The door handing process was not executed during installation. Here are the …Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).2. Enter new Mastercode.3. Press Lock button once.4. Re-enter Mastercode.5. Press Lock button once.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure the Mastercode has not already been programmed.The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. Life Experiences. ... Yes, the lock will beep 10 times and flash red approximately 6 weeks prior to running out. Read More . Answer How to Replace The Batteries In SmartCode 955? ...Switch:1 = Door lock status LED blinks every 6 seconds2 = Lock automatically re-locks door 30 seconds after unlocking.3 = Audio4 = Not used.LED Color:Blinking green = UnlockedBlinking amber = LockedBlinking red = Low batterySolid red = Door handing process did not work properly.Keypad WarningsKeypad flashes red with fast beeping sound* for 3 ...The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. ... Can I turn off the beeping sounds on the Home Connect 620 Smart Lock? ... Yes, the following lock settings can be turn on/off: LED; Audio/Beeps; Auto-Lock; Click here for instructions. Connect with us. Monday-Friday: 7:00am-4:00pm PST ...

The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. ... on. Use a fresh set of batteries and perform the door handing process. If the latch does not extend or retract, and the lock does not beep, press each individual key on the keypad (one at a time) and listen for beeping sound. If no beeping ...14 Nov 2023 ... If your Kwikset SmartCode 909 is constantly flashing red and beeping, it indicates low battery power, and you need to replace the batteries ...The Deadbolt Does Not Lock The Door And Kevo Convert Beeps/Lights Up Red. This is a 'bolt jam' alert. It means that Kevo Convert was unable to extend the deadbolt and your door was not locked. This happens when the door was not shut properly and the deadbolt could not fully extend into the strike hole. On my Powerbolt 2, the keypad flashes red 3 times with 3 beeps. There are four reasons for this to occur: 1. Door jammed while attempting to lock. Manually re-lock door. If needed, reposition strike. 2. Door handing code has not been entered. Enter door handing code. 3. No User Code programmed, or User Codes are disabled. Keep door open. Press and HOLD the Program button until the keypad Flashes green (about 5 seconds).2. Press Lock button once.3. Enter Mastercode.4. Press Lock button once.5. Re-enter Mastercode.6. Press Lock button once.If programming is unsuccessful, the keypad will fl ash red three times with three beeps.SmartKey Security™ re-key technology is compatible with Kwikset (KW1) keyway or (SC1) keyway options. Comes with 2 keys. Deadbolt Latch has 2 interchangeable faceplates - round corner and square corner. ANSI/BHMA grade 2 certified. Latch has adjustable backset 2-3/8" to 2-3/4" to fit all standard door preparations.To lock your door, place any finger on the fingerprint sensor. The light bar will display the following animations, beep once, and the door will lock. To unlock your door, place your enrolled finger on the fingerprint sensor. The light bar will display the following animations, beep once, and the door will unlock. Locking Unlocking Orange sweep, On my Smartcode Lever, Keypad flashes red 6 time with 6 beep (beeping sound will only be heard if switch #3 is on) Attempt programming procedure again, making sure not to pause for more than 5 seconds.

Kwikset locks use four AA batteries, which should last for about a year. If your lock is blinking green and beeping, try replacing the batteries with a fresh set and see if that resolves the issue. Second, the blinking green and beeping could mean that your lock is in programming mode.Kwikset to order a drive-in latch for your lock. Latch and Strike Exterior Assembly Interior Assembly Levers and screws Parts in the Box Kwikset 1-800-327-5625 www.kwikset.com 1-3/4 " (44 mm) 1-3/8 " (35 mm) 2-3/8" (60 mm) 2-3/4" (70 mm) Template If your door requires drilling, cut out the template and place it on the exterior side of the door ... On my Smartcode 909/910, the lock beeps, the keypad flashes red, and the door cannot lock. The door handing process was not executed during installation. Here are the instructions for the door handing: Remove battery pack. Press and HOLD the Lock button while installing battery pack. Hold button until the latch bolt starts moving on its own. If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps. Note: If the lock is muted, you will not hear the lock beeping. Connect with us. ... Note: If the lock is muted, you will not hear the lock beeping. Connect with us. Monday-Friday: 7:00am-4:00pm PST. Saturday: 6:30am-2:30pm PST. Sundays & Major Holidays: Closed.

Anmed central.

If needed, the door handing process can be initiated manually. This is useful if the lock is being moved to a different door Remove battery pack. Press and HOLD the Program button while reinserting the battery pack. Release button once battery pack is installed. The status LED will flash red and green. Press the Program button once more.Perform the door handing process once the lock is fully installed. ©2014 Kwikset Corporation 4970 / 01 4 / 11 Technical upport 1-86-83-6584 ... B The Status LED is solid red after the door handing process. The lock interior is not mounted perpendicular ... the lock does not beep, press each individual key on the keypad (oneControl locks from anywhere. Smart Home Integration. About Smart Locks. Browse all smart locks. ... The Kwikset Home. Security on the outside, convenience on the inside. ... If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step 1. Connect with us. Monday-Friday: 7:00am-4:00pm PST. Saturday: 6:30am-2:30pm PST ...Inspect the Batteries. If your Kwikset SmartCode 913 is not working properly (won’t lock/unlock, the keypad not responding, etc.), start your troubleshooting by inspecting the batteries. The battery polarities may have reversed, causing the lock to stop working. Go to the interior assembly of your lock and remove the interior cover.

Please ensure you have pressed and held the reset button for 5 seconds and heard three long beeps. Please ensure you have used the default master code to reset your lock. For more information about resetting the Kwikset lock, please check this article: How To Reset Kwikset Lock Code Without Key? Detailed Guide. Kwikset Powerbolt 2 3 …Switch:1 = Door lock status LED blinks every 6 seconds2 = Lock automatically re-locks door 30 seconds after unlocking.3 = Audio4 = Not used.LED Color:Blinking green = UnlockedBlinking amber = LockedBlinking red = Low batterySolid red = Door handing process did not work properly.Keypad WarningsKeypad flashes red with fast beeping sound* for 3 ...See Kwikset smart locks that work with your smart phone and other smart home solutions. Browse Smart Locks. Blog Articles & Inspiration. Security a Top Concern Among Recent Home Buyers. Obsidian Cutting Edge Design Meets Keyless Entry. SmartCode 915 Designed to Solve Real Life Challenges.Solution 3: Addressing an Invalid User Code. Solution 4: Incorrect Installation. Solution 5: Managing Technical Faults. Tricks and Tips: Navigating Your Schlage Lock More Effectively. Tip 1: Regularly Check Your Batteries. Tip 2: Keep Your Programming Code Handy. Tip 3: Regular Software Updates.Why is my Kwikset lock flashing red and beeping? Program at least one user code and test the Lock button again. The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set.On my Powerbolt 2, the keypad flashes red 10 times with 10 beeps. Low battery. Replace batteries.The Kwikset app's Lock Activity screen conveniently displays all of Halo's activity including actions such as locking, unlocking, low battery warning, manual key-based entries, and other alerts. ... Audible beeps and visual flash when batteries are low. 20 Minute Fire Rating. 20 Minute Fire Rating (UL logo) Code Alarm.The keypad flashes red ten times with ten beeps: Low battery. Replace batteries. Lock beeps two times/keypad flashes red three times/keypad flashes red six times with six beeps: Programming timeout. Attempt the programming procedure again, making sure not to pause for more than 5 seconds. The keypad flashes red 15 times and beeps 15 times.Before reinstalling the battery cover, locate the reset button on the lock. Press and hold this button for 5 seconds or until you hear 3 distinct beeps from the lock. This resets the lock and should stop any unwanted beeping. Once you have finished this step, go ahead and reinstall the battery cover.Hold the button continuously for 30 seconds until you hear a beeping sound and see the status LED flashing red. Press the program button once again until you see the status LED flashing green and hear two beeping sounds. The Kwikset SmartCode deadbolt lock has now been reset and ready to be set up again. To confirm if the process is complete ...1 Long beep = Programming successful. 2 Long beeps = Enter Programming mode. 3 Short beeps = User code is not yet set, Setting unsuccessful, Wrong user code, Lockout mode. 4 Long Beeps = Handing is not yet set. 5 Short Beeps = Time out for programming mode. 10 Long beeps = Low battery alarm. 15 Short beeps = 3 consecutive incorrect …

Press and HOLD the Program button until the Checkmark symbol illuminates (about 5 seconds). Press Checkmark symbol once. Enter new Mastercode. Press Lock symbol once. Re-enter Mastercode. Press Lock symbol once. If programming is successful, the Checkmark will illuminate and you will hear one beep.

It is recommended that you delete this code.1. Make sure the lock is unlocked and the door is open.2. Enter your existing Mastercode.3. Press the lock button. You will hear one beep.4. Press 3.5. Press the lock …For example, SmartCode 913 flashes red three times accompanied by three beeps, while SmartCode 914 and 888 locks signal one beep and one flash. The Obsidian model, on the other hand, shows an “X” pattern accompanied by one beep.Red Flash: The 4 AA batteries in the Kevo interior are low and need to be replaced. Kwikset Kevo smart lock manual. The Kwikset Kevo smart lock is a well-liked product that lets you control your door from your smartphone. It's easy to install, but sometimes, things can go wrong, and it cannot be easy to troubleshoot when they do. Blinking red = Low battery Solid red = Door handing process did not work properly. Keypad Warnings Keypad flashes red with fast beeping sound* for 3 – 4 seconds. Three possible reasons and solutions: 1. Low battery - Replace batteries 2. Door jammed while attempting to lock - Relock door. If needed, reposition strike. 3. The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. Life Experiences. ... On my Smartcode 888, the lock button flashes red with fast beeping sounds for three to four seconds This is a low battery alert. Please replace you batteries.First, ensure that your mobile device, whether it's a phone or a tablet, has Bluetooth enabled and is linked to the door lock. In the event that it does not pair with the lock, you will need to reset the connection. Proceed to your device's settings menu (the location will vary depending on your operating system).Touch lower left area of screen (where Checkmark is located) until digits illuminate.3. Touch screen with three or more fingers until digits illuminate.One-second pauseThe lock requires a one-second pause immediately after locking or unlocking before the touchscreen will re-activate.Control locks from anywhere. ... The Kwikset Home. Security on the outside, convenience on the inside. ... Yes, the lock will flash red lights and beep 10x in a row ...If you hear 1 short beeps and 1 long red flash, it means that the lock auto locks. If you hear 2 short beeps, it means that the turnpiece rotated to unlock position. If you hear 1 long beep, it means that the turnpiece rotated to locked position. If you hear 10 short beeps and 10 short red flashes, it means low battery. If you hear 15 long ...

Www activategen com.

Vrcc veterinary specialty and emergency hospital.

To do so, open the door and then press the program button. Press the checkmark symbol once and then the lock symbol once. Enter the code you wish to remove and press the lock symbol again. Input the code once more. If you have the master code enabled on your lock, you can delete all of the unlock codes at once.Follow these easy steps to give your Kwikset locks a fresh start: Take off the battery cover and pull out the battery pack. Press and Hold the program button for 5 seconds. In some models, you must keep holding that Program button for approximately 30 seconds until your lock flashes a red light and a beep.Battery life is estimated at 1 year based on 10 uses per day. The more that the Kevo is used, the lower the overall battery life. The highest drain on your batteries within the Kevo system is the motor that drives the lock mechanism. Make sure that the deadbolt and strike are aligned properly so that there is no unnecessary resistance, as this ...The keypad flashes red ten times with ten beeps: Low battery. Replace batteries. Lock beeps two times/keypad flashes red three times/keypad flashes red six times with six beeps: Programming timeout. Attempt the programming procedure again, making sure not to pause for more than 5 seconds. The keypad flashes red 15 times and beeps 15 times.If the issue only occurs when the door is closed, check on the following causes: 1. Door prep - ensure proper strike hole depth in the door frame. - Adjust tab on lower strike to center deadbolt head - Ensure deadbolt strike is at least 1" deep on frame of door - Check that door thickness is supported - 1-3/8" to 1-3/4 2. Do you need to ...To maximize battery life, disable these functions by adjusting the switches on your Kwikset smart lock. For example, if you own a SmartCode 913 model, set switches #1, #2, and #3 to the OFF position. Switch #1 controls the LED, #2 manages the auto-relocking, and #3 determines the audio functionality.Watch this video to find out how to use powdered graphite to fix a door lock that doesn't turn easily. Expert Advice On Improving Your Home Videos Latest View All Guides Latest Vie...green and you will hear 2 beeps. If unsuccessful, the Kwikset button will flash red and you will hear 3 beeps (make sure the door is open and unlocked and that you are using a fresh set of batteries). 6. Test the lock: With the door open and unlocked, press Kwikset. Make sure it locks the door. 7. Test the default User Code: Enter the default ...Replace the old batteries with the new ones, taking note of the battery orientation. Before putting the battery cover back on, locate the reset button on the lock. Press the reset button firmly and hold it for around 5 seconds or until you distinctly hear three beeps.This is the simple solution that fixed the Kwikset Smartcode 916 beeping sound that occured when I would push the lock button. It would unlock fine, but it ...Rotate the key 90 degrees clockwise. Insert the SmartKey tool fully and firmly into the SmartKey hole. You may feel the tool click inside the lock. Remove the SmarKey tool. Remove the current key. Insert the new key you wish to use with the lock. Make sure your key is FULLY inserted. The edge of the key touches the indent in the cylinder face. ….

Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).2. Enter new Mastercode.3. Press Lock button once.4. Re-enter Mastercode.5. Press Lock button once.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure the Mastercode has not already been programmed.On my 264 deadbolt, the door can be locked with the Kwikset button, but the User Code will not unlock the door. Make sure the User Code is correct and that the Kwikset button is pushed after entering the User Code. If the door still won’t unlock, use a key to unlock the door. Call technical support for further troubleshooting.First, ensure that your mobile device, whether it's a phone or a tablet, has Bluetooth enabled and is linked to the door lock. In the event that it does not pair with the lock, you will need to reset the connection. Proceed to your device's settings menu (the location will vary depending on your operating system).Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).2. Enter new Mastercode.3. Press Lock button once.4. Re-enter Mastercode.5. Press Lock button once.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure the Mastercode has not already been programmed.The red LED will illuminate when the lock enters Add Mode. Please allow time for the controller to add the lock. 3. If successful, re-name the lock in your system (if applicable).4. If unsuccessful, follow your system's instructions to remove the lock form the controller and any other network, then press button "A" on the lock on time.If you need to rekey locks, Lowe's may come to mind. But does Lowe's rekey locks? We answer whether there is a Lowe's rekey service. Details inside. Lowe’s rekeys locks at most of ...Perform the door handing process, following the instructions inside the installation guide. The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set. The mounting plate is placing tension on the torque blade.KeyCorp Looks Locked Out Right Now...KEY During Wednesday's Lightning Round of Mad Money one caller asked Jim Cramer about KeyCorp (KEY) . "This is a great company but that 7% yiel...If needed, the door handing process can be initiated manually. This is useful if the lock is being moved to a different door Remove battery pack. Press and HOLD the Program button while reinserting the battery pack. Release button once battery pack is installed. The status LED will flash red and green. Press the Program button once more.16 Feb 2024 ... Is your Kwikset SmartCode 913 flashing red and beeping consistently ... How To Operate The Kwikset 264 Contemporary Electronic Deadbolt Door Lock. Kwikset lock beeping red, 3.2 The lock beeps, the keypad flashes red, and the door cannot lock. 3.3 The Status LED is solid red after the door handing process. 3.4 The deadbolt latch does not extend or retract on its own during the door handing process. 4 Troubleshooting: Keypad. 4.1 The keypad is unresponsive. 4.2 The Lock button does not lock the door., The first thing to do is to troubleshoot Kwikset batteries issues when your Kwikset lock is beeping . When the batteries on your Kwikset lock are low, the lock will beep and the LED light on the lock will flash red. If you hear the lock beeping or see the LED light flashing red, it is time to replace the batteries. Kwikset recommends using high ..., Main page; Simple start; Simple talk; New changes; Show any page; Help; Contact us; Give to Wikipedia; About Wikipedia, Aura Smart Lock; Smart Locks Basics. Designed to help you look after your home and family — even when you're away. Compare Smart Locks. Works With. App. Aura. Halo. Obsidian. ... On my 264 Deadbolt, the Kwikset button flashes red 5 times You've entered 5 incorrect user codes within one minute. Please re-enter your user code after 45 seconds., Note: During the pairing process, the Status LED will flash red and green, followed by a short beep (if the lock's sound is not muted). Sound The lock beeps during normal use and programming. If desired, you may mute the lock inside the Premis app. Note: Beeping will not be heard if the lock's sound is muted., There are two low battery indicators on the unit. The LED light on the interior side of the lock will flash red when the batteries are low. The keypad will also flash red when the batteries are low. Why does my Kwikset lock beep and flash red? The Deadbolt Does Not Lock The Door And Kevo Convert Beeps/Lights Up Red. This is a 'bolt jam' alert., Just follow the instructions included. I did have a little problem with adding in code numbers. It kept beeping and showing red on the kwikset button. After trying about 6 times and calling it some four letter words and letting it sit for a few minutes, it finally took the code number and turned green (kwikset button). Works as it should., Home / Support / Answers. On my Smartcode 888, the lock button flashes red three times with three beeps. There are two reasons for this to occur: 1. No user code programmed. …, The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. ... on. Use a fresh set of batteries and perform the door handing process. If the latch does not extend or retract, and the lock does not beep, press each individual key on the keypad (one at a time) and listen for beeping sound. If no beeping ..., To reset your Weiser Powerbolt 2: Make sure the door is open and unlocked. Press and hold the Reset button for 5 seconds until you hear three long beeps. Enter the default Mastercode (O-O-O-0). Press the "Unlock" button. You will hear one beep. Press the 0 button. Press the "Unlock" button., Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).2. Enter new Mastercode.3. Press Lock button once.4. Re-enter Mastercode.5. Press Lock button once.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure the Mastercode has not already been programmed., The first thing to do is to troubleshoot Kwikset batteries issues when your Kwikset lock is beeping . When the batteries on your Kwikset lock are low, the lock will beep and the LED light on the lock will flash red. If you hear the lock beeping or see the LED light flashing red, it is time to replace the batteries. Kwikset recommends using high ..., About 6 minutes after they were off and I turned one more light off manually my Kwikset door unlocked on it's own. Of course I set straight up in bed wondering if the door was about to be opened, but I know I had not heard the beeps of a code being pushed in, so I figured something had gone wrong. This is what I find in the log., Perform the door handing process, following the instructions inside the installation guide. The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set. The mounting plate is placing tension on the torque blade., Peace of mind is priceless. Kwikset's SmartKey Security is designed to protect against advanced break-in techniques and its patented design is pick-resistant and bump-proof. SmartKey Security also allows you to re-key the lock yourself in seconds, rendering lost or stolen keys useless. About SmartKey Security., On my Smartcode 909/910, the lock beeps, the keypad flashes red, and the door cannot lock. The door handing process was not executed during installation. Here are the instructions for the door handing: Remove battery pack. Press and HOLD the Lock button while installing battery pack. Hold button until the latch bolt starts moving on its own., Step 3: Re-enter the Master Code and press the Lock button. The keypad will flash red and beep three times, indicating the Master Code is successfully enabled. So that's all about enabling Master Code on a Kwikset lock. Disabling/Deleting Master Code. Step 1: Press and hold the Program button for about 5 seconds—until it flashes green., 3.2 The lock beeps, the lock button flashes red, and the door cannot lock. 3.2.1 B1. 3.2.2 B2. 3.2.3 B3. 3.2.4 B4. 3.2.5 B5. 3.2.6 B6. 3.2.7 B7. 3.2.8 B8. 3.2.9 B9. 3.2.10 B10. 3.3 The Status LED is solid red after the door …, If the issue only occurs when the door is closed, check on the following causes: 1. Door prep – ensure proper strike hole depth in the door frame. - Adjust tab on lower strike to center deadbolt head - Ensure deadbolt strike is at least 1” deep on frame of door - Check that door thickness is supported - 1-3/8" to 1-3/4 2. Do you need to ... , On my Smartcode 909/910, the lock beeps, the keypad flashes red, and the door cannot lock. The door handing process was not executed during installation. Here are the …, This is indicated by the keypad flashing red three times with three beeps. Use a fresh set of batteries, and perform the door handing process again. The latch ..., Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).2. Enter new Mastercode.3. Press Lock button once.4. Re-enter Mastercode.5. Press Lock button once.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure the Mastercode has not already been programmed., Please call technical support for further Kwikset smart lock troubleshooting if still not. The Kwikset Powerbolt lock keys are not working. If your key can not open your Kwikset Powerbolt 2 lock, please ensure you use the right key first. Otherwise, you can try to rekey your Kwikset lock to create a new key. Then, try to use this new key to ..., Release the “Program” button once the lock beeps and the LED flashes red; The lock is now reset to factory settings; Note: This will erase any existing settings, including user codes and lock configurations. Reprogramming the Lock. After a factory reset, you will need to reprogram your Kwikset smart lock in order to use it correctly. …, Home / Support / Answers. On my Smartcode 888, the lock button flashes red three times with three beeps. There are two reasons for this to occur: 1. No user code programmed. …, Control locks from anywhere. Smart Home Integration. About Smart Locks. Browse all smart locks. Featured. ... The Kwikset Home. Security on the outside, convenience on the inside. Explore a world of innovations. ... Keypad flashes green with continuous beeping sound for two seconds., The red LED will illuminate when the lock enters Add Mode. Please allow time for the controller to add the lock. 3. If successful, re-name the lock in your system (if applicable).4. If unsuccessful, follow your system's instructions to remove the lock form the controller and any other network, then press button "A" on the lock on time., Aura Smart Lock; Smart Locks Basics. Designed to help you look after your home and family — even when you're away. Compare Smart Locks. Works With. App. Aura. Halo. Obsidian. Premis. Halo Touch . Browse Smart Locks. View and compare all smart locks. Innovation. The Kwikset Home. Security on the outside, convenience on the inside. Explore a ..., Monday-Friday: 7:00am-4:00pm PST. Saturday: 6:30am-2:30pm PST. Sundays & Major Holidays: Closed. For countries outside the U.S. and Canada, please visit our International contact page. Get Support on your Obsidian Keywayless Deadbolt., Make sure switch #3 is on, and press the Program button once. If you hear three beeps andNote: The lock will time out after five seconds.Disabling and Deleting the Mastercode1. Keep door open. Press and HOLD the Program button until the keypad Flashes green (about 5 seconds).2. Press Lock button once.3. Enter Mastercode.4. Press Lock button once.5., Press Lock button once7. Press “9” six times.8. Press Lock button once.If programming is successful, the keypad will flash green once with one beep.If programming is unsuccessful, the keypad will fl ash red three times with three beeps. Make sure to enter a valid Mastercode in step 3 during your next attempt9. , 2 days ago · The keypad flashes red ten times with ten beeps: Low battery. Replace batteries. Lock beeps two times/keypad flashes red three times/keypad flashes red six times with six beeps: Programming timeout. Attempt the programming procedure again, making sure not to pause for more than 5 seconds. The keypad flashes red 15 times and beeps 15 times. , To keep your wheels rotating at the same speed, you can manually lock your rear differential. Learn how to lock the rear differential in this article. Advertisement The three jobs ...